ClickCease
BOOK ONLINE HERE & SAVE 10%
Asko Washer Foul Odors

Asko Washer Foul Odors

01 – Asko Washing Machine Rotor and Stator Kit

The stator is part of a direct drive motor that electrically drives the outer rotor. If the stator coils become wet or the coated wires on the coils short out, they can produce a burning smell. You can test the stator coils with a meter. If the stator is smoking, or smells burnt, it will need to be replaced.

02 – Asko Washing Machine Main Control Board

The main control board provides power to the various components of the washer. If the control board receives a power surge, or a component fails, the control board can short-out causing a burning smell. Inspect the control board for burn marks. A burnt main control board will need to be replaced.

03 – Asko Washing Machine Motor Control Board

The motor control board sends power to the motor. If the motor shorts out or a power surge occurs components on the board can blow out causing a burning smell. Inspect the motor control board for burn marks and replace if necessary.

04 – Asko Washing Machine Control Board

The control board provides power to the components of the washer. If the control board receives a power surge or a component fails, the control board can short out causing a burning smell. Inspect the control board for burn marks. If the control board is burnt, it will need to be replaced.

05 – Asko Washing Machine Water Pump Belt

The water pump belt can get worn and slip on the pulleys causing a burning smell. Check the motor pulley for wear and make sure the water pump turns freely.

06 – Asko Washing Machine Drive Belt

If the drive belt is worn or frayed it can slip on the pulley causing friction and a burning smell. Also check the components the belt is turning to make sure they turn freely. A stuck water pump or idler pulley can create enough friction to cause the belt to burn.

07 – Asko Washing Machine Belt Kit

Some washer models use two belts, one to run the transmission and one to run the water pump. If the belts become worn or burnt, they can be replaced together as a kit. A stuck water pump or transmission can create enough friction to cause the belt(s) to burn.

08 – Asko Washing Machine Timer

Contacts in the timer can become worn over time and not make good contact. When this happens the contacts can overheat, arc, and you may get a burning smell from the timer.

09 – Asko Washing Machine Drive Motor

The drive motor operates the mechanical components of the washer. If one of the components fails the motor may stop or strain to keep turning. Sometimes the motor itself can have bad bearings making the motor shaft hard to turn. When this happens the windings can overheat causing an electrical burning smell. If the motor hums but won’t start or the windings smell burnt it will likely need to be replaced.

10 – Asko Washing Machine Drive Pulley

Some washer models will have a removable drive pulley attached to the drive motor shaft to rotate the drive belt. If the transmission is locked up or the pulley is worn or damaged, the belt can slip on the pulley and produce a burning rubber smell. Inspect the drive pulley for any wear or damage and replace as necessary.

11 – Asko Washing Machine Wire Harness

A damaged washer wire harness could be producing the burning smell. Inspect the appliance’s wire harnesses to determine if any frayed or disconnected wires are present, then replace the component if necessary.

12 – Asko Washing Machine Inverter Board

The washer’s inverter board assists in determining how fast the tub will spin and in what direction during the spin cycle. If the board has shorted or worn out, it can produce a burning smell. You should inspect the inverter board for signs of burning or a shorted-out component and replace if necessary.

13 – Asko Washing Machine Drain Pump

Make sure the pump turns freely. It is fairly common for small clothing items especially baby socks and lint to get stuck in the pump. If the pump impeller can’t move, either the belt or motor will get hot causing a burning smell.

14 – Asko Washing Machine Clutch

Some top load washers use a clutch to spin the inner tub. If the clutch gets worn the clothes may come out wet and you may smell a slight burning odor.

15 – Asko Washing Machine Idler Pulley

The idler pulley keeps tension on the belt to keep the belt tight. If the pulley bearing is not moving freely the belt will slip on the pulley and cause a burning rubber smell.

16 – Asko Washing Machine Transmission

On top load models, a locked-up transmission can case the belt to slip on the motor pulley causing the belt to burn. Confirm the transmission is turning freely and the belt is not burnt.

17 – Asko Washing Machine Idler Pulley Lever

Some top load models use an idler pulley to keep tension on the belt. If the idler arm or pulley do not move freely the belt can slip causing a burning smell.

18 – Asko Washing Machine Motor Pulley

Motor pulleys are made of either metal or plastic materials that can wear down over time. Inspect the motor pulley for signs of damage or wear. A worn pulley can cause friction which can cause the belt to burn.

19 – Asko Washing Machine Clutch Band Kit

Some top load washers use a clutch to spin the inner tub. If the clutch gets worn the clothes may come out wet and you may smell a slight burning odor. You can fix the problem you can install a new clutch band kit, if applicable to the model.

20 – Asko Washing Machine Stator Assembly

A washing machine stator interacts with a rotor to spin or agitate the tub during the wash and spin cycles. An overheated or worn out stator can produce a burning smell. You should inspect the component for signs of damage or to determine if the stator smells burnt, then replace if necessary.